Tech Bulletin / Addendum

DepartmentTelephoneEmail AddressName
Service & Technical Support Department
1-800-227-6937
service@vanner.com
Service & Technical Support Department
(Department Manager)		Office (614)-771-3512
1-800-227-6937 x3512		jamesf@vanner.comJames Finley
(Department Manager)
Vehicle System Integration Team
(VSIT Manager)		Office (614) 771-3540
Mobile (614) 329-1495		mikeo@vanner.com
vsiteam@vanner.com		Mike O'Sullivan
(VSIT Manager)
Vehicle System Integration Team
Mobile (614) 329-1589
Mobile (215) 601-0415		jeffc@vanner.com
mikew@vanner.com		Jeff Carey (Truck)
Mike Westerfer (Bus)

SERVICE CUSTOMER – DATA COLLECTION FORM (pdf)
 
RETURN GOODS AUTHORIZATION FORM (pdf)

Tech Bulletin / Addendum

Product NameOwner's Manual(s)NotificationEffective Date
Bravo Discontinuation Notice
Bravo 1800 (BRC12-1800SH)		LSC12-2000 Owner's ManualBravo Discontinuation Notice Bravo 1800 (BRC12-1800SH)Feb. 22, 2022
Product Discontinuation Notice / Last Time Buy Legacy Battery Equalizers and DC-DC Converters Product Discontinuation Notice / Last Time Buy Legacy Battery Equalizers and DC-DC Converters April 25, 2022April 25, 2022
Vanner LifeStar™ Inverter Discontinuation Notice (20-1050CUL-DC, 20-1000TUL-DC)Vanner LifeStar™ Inverter Discontinuation Notice (20-1050CUL-DC, 20-1000TUL-DC)Dec. 06, 2021
BYBON GFCI ReceptacleOwner's Manual
BYBON GFCI_NotificationMay 30, 2019
IQC Ambulance Mode
Technical Bulletin		 IQC Ambulance Mode
Technical Bulletin		Nov. 29, 1999
20-1050CUL, 20-1050CUL-DC Troubleshooting Guide1050_Troubleshooting_A820085-AFeb. 01, 2021
LSC12-2000 Technical BulletinOwner's ManualLSC12-2000 STUD TORQUE A820706-ASept. 01, 2022

(Support) Frequently Asked Questions

Product NameOwner's Manual(s)FAQ / Model Numbering
20-1000TUL-DCOwner's ManualF.A.Q.
20-1050CUL-DC & 20-1000TUL-DCOwner's ManualF.A.Q.
BYBON GFCI RECEPTACLEOwner's Manual
BYBON GFCI_NOTIFICATION
CONVERTER-90-CAN-SERIESOwner's ManualModel Numbering
EQUALIZER 70-SERIES & 71-SERIES70 Series Owner's Manual
71 Series Owner's Manual		F.A.Q.
EQUALIZER 70M-SERIESOwner's Manual
F.A.Q.
EQUALIZER-70-CAN-SERIESOwner's ManualF.A.Q.
EQUALIZER-80-CAN-SERIES80 Series Owner's Manual
81 Series Owner's Manual		Model Numbering
F.A.Q.
HYBRID BELTLESS ALTERNATOROwner's Manual
idleWATCHII®Owner’s ManualModel Numbering
SP00158 12V-24V DC-DC ConverterOwner's Manual
F.A.Q
VANNER CAN INTERFACE USER MANUAL REV5.0Owner's Manual

FAQ for 20-1000TUL-DC

1. Why does my inverter put out low A/C voltage (90-100 volts)?

    • Answer: A/C output must be measured with a True RMS meter in order to read the voltage correctly. A low voltage reading is normal with an average reading meter.

2. Why is my inverter output only approx. 40VAC?

    • Answer: The inverter is in Load Demand. When the inverter has no load it goes into load demand & only puts out approx. 40VAC. Plug a load in & inverter output will come up to 120VAC. To turn load demand off, turn the load demand dip switch off (down).

3. Can I use the IFM1 with the 20-1000TUL-DC?

    • Answer: Yes

4. Does it matter which modular connector I put the IFM1 cable in?

    • Answer: No.

5. Why won’t my inverter turn on?

    • Things to check:

5.1 With no remote: Verify that switches 4 and 5 are down (closed).

5.2 Using ignition remote: Verify 12 volts is on position one of the connector and that switch 4 is up and switch 5 is down.

5.3 Using ground remote switch: Ground wire is connected to the center position of connector. Switch 4 must be down and switch 5 up.

5.4 If you are using both: Switches 4 and 5 must be up with the proper connections.

5.5 Input DC cables must be connected to battery.

5.6 Verify at the back of the inverter that there is 12 volts on the DC input cables.

6. Why am I getting no A/C Output from my inverter when the inverter LED is on solid?

    • Answer: Check to see if GFCI is tripped. Reset if necessary.

7. Although my inverter works, why does it do nothing when plugged into shore power?

    • Answer: Verify AC input (110VAC) is getting to the inverter.

FAQ for 20-1050CUL-DC & 20-1000TUL-DC

1. Why does my inverter A/C voltage output read low (90-100 volts)?

    • Answer: A/C output must be measured with a True RMS meter in order to read the voltage correctly. A low voltage reading is normal with an average reading meter.

2. Why does my inverter output only read approximately 40VAC?

• Answer: The inverter is in Load Demand. When the inverter has no load it goes into load demand & only outputs approximately 40VAC. Plug a load in & inverter output will come up to 120VAC. To turn load demand off, turn the “Load Demand” dip switch off (down).

3. Why are my batteries overcharging? (Applies to 20-1050CUL-DC only)

    • Answer: The high/low charger switch is in the low position, there is too much current draw on the batteries and the charger can’t come out of bulk mode or it is cycling often from float to bulk mode. Change the battery charge rate from low to high. ( dip switch three)

4. Can I use the IFM1 with the 20-1000TUL-DC?

    • Answer: Yes

5. Can I use the IFM1 with the 20-1050CUL-DC?

    • Answer: Yes

6. Does it matter which modular connector I put the IFM1 cable in?

    • Answer: No

7. Why won’t my inverter turn on?

Things to check:

    • 7.1 With no remote: Verify that switches 4 and 5 are down (closed).
    • 7.2 Using ignition remote: Verify 12 volts is on position one of the connector and that switch 4 is up and switch 5 is down.
    • 7.3 Using ground remote switch: Ground wire is connected to the center position of connector. Switch 4 must be down and switch 5 up.
    • 7.4 If you are using both: Switches 4 and 5 must be up with the proper connections.
    • 7.5 Input DC cables must be connected to battery.
    7.6 Verify at the back of the inverter that there is 12 volts on the DC input cables.

8. Why am I getting no A/C Output from my inverter when the inverter LED is on solid?

    • Answer: Check to see if GFCI is tripped. Reset if necessary.

9. When inverter is plugged into shore power why are my batteries not being charged? (Applies to 20-1050CUL-DC only)

    • Answer: Verify 110 volts at A/C input cable.

10.Although my inverter works, why does it do nothing when plugged into shore power?

    • • Answer: Verify DC is present at DC input connector.

(Applies to 20-1050CUL-DC only)

• Answer: Verify AC input (110VAC) is getting to the inverter. (Applies to 20-1000TUL-DC only)

FAQ for EQUALIZER 70 & 70M-SERIES

1. How do I verify that my equalizer is functioning properly?

    • • Answer: 1. Measure 24V to ground at the equalizer, note voltage.

 

    • Answer: 2. Measure 12V to ground at the equalizer, note voltage. The 12V output should be half of the 24V voltage with approximately 2 Amps applied.

2. Why is the green LED on my equalizer not on? (Applies to 70M equalizer only)

    • Answer: Deutsch connector not connected or pin B of Deutsch connector is not receiving 24VDC.

FAQ for EQUALIZER 70-CAN-SERIES

1. How do I verify that my equalizer is functioning properly?

  • Answer:
  • 1. Measure 24V to ground on the equalizer, note voltage.
  • 2. Measure 12V to ground on the equalizer, note voltage. The 12V output should be half of the 24V voltage with approximately 2 Amps applied.

2. Why is the green LED on my equalizer not on?

  • Answer: Deutsch connector not connected or pin B of Deutsch connector is not receiving 24VDC.

FAQ for EQUALIZER 80-CAN-SERIES

1. How do I verify that my equalizer is functioning properly?

  • Answer:
  • 1. Measure 24V to ground on the equalizer, note voltage.
  • 2. Measure 12V to ground on the equalizer, note voltage. The 12V output should be half of the 24V voltage with approximately 2 Amps applied.

2. Why is the green LED on my equalizer not on?

  • Answer: Deutsch connector not connected or pin B of Deutsch connector is not receiving 24VDC.

 

FAQ for SP00158

1. How do I verify that my converter is functioning properly?

Things to check:

    1. 1. Measure 12V to ground on the converter, note voltage. The input voltage should be between 11.4 to 20 VDC with a minimum start up voltage of 12.5 VDC.

2. Measure 24V to ground on the converter, note voltage. The output voltage should be 27.5 VDC.

2. Why is my output voltage low?

Answer: The load is exceeding the 45 amp rating and the unit is going into current limit.

3. Why doesn’t my unit start?

Answer: The 12 volt supply is below the minimum start voltage of 12.5 VDC.